Welcome Offer : Use Code WELCOME5 for 5% OFF your first order!
Free Shipping on Most USA Orders
Welcome Offer : Use Code WELCOME5 for 5% OFF your first order!
Free Shipping on Most USA Orders
Welcome Offer : Use Code WELCOME5 for 5% OFF your first order!
Free Shipping on Most USA Orders
Welcome Offer : Use Code WELCOME5 for 5% OFF your first order!
Free Shipping on Most USA Orders
Welcome Offer : Use Code WELCOME5 for 5% OFF your first order!
Free Shipping on Most USA Orders
Welcome Offer : Use Code WELCOME5 for 5% OFF your first order!
Free Shipping on Most USA Orders
Welcome Offer : Use Code WELCOME5 for 5% OFF your first order!
Free Shipping on Most USA Orders
Welcome Offer : Use Code WELCOME5 for 5% OFF your first order!
Free Shipping on Most USA Orders
Welcome Offer : Use Code WELCOME5 for 5% OFF your first order!
Free Shipping on Most USA Orders
Welcome Offer : Use Code WELCOME5 for 5% OFF your first order!
Free Shipping on Most USA Orders
Some products sold on this website may expose you to chemicals known to the State of
California to cause cancer, birth defects, or other reproductive harm.
All electrical products must be installed by a qualified electrician in accordance
with local wiring regulations. Incorrect installation may result in fire, electric
shock, or injury.
Always disconnect power at the circuit breaker before installation.
💡
Bulb & Usage Advisory
Do not exceed the maximum wattage specified on the fixture label.
Keep away from flammable materials. Allow adequate ventilation around the fixture.
Keep out of reach of children. Not suitable for wet locations unless rated IP65 or higher.
E-Simpo 4W G23 LED Bulb 2-Pin LED PL Retrofit Lamp CFL 7W Replacement 180 View Angle Daylight 6000k LED PL Horizontal Recessed Down Light Bulb(Need Bypass Ballast) (Cold White, 4W 135mm)Specification Input Voltage: Both 110V 220V AC Power: 4W NO Dimmable CRI>82 LED: SMD2835 Brightness: 4W 350-450Lumens Color Temperature: Warm White 3000-3500K; Cold White 6000-6500K Please check the PL Lamp fixture or table light fixture for allowed install length before you decide. Size: 4W: L135*D27mm/L5.3*D1.0 Application: 3W is used to Replace 2-Pin CFL PL-S 5W 4W is used to replace 2-Pin CFL PL-S 7W Note: 1. Please check if the inside ballast is inductive ballast or electronic ballast; 2. If it is inductive ballast, you can use this LED lamp directly, just plug and play. 3. If it is electronic ballast, the led driver can not work compatibly with the electronic ballast, so you have to bypass the electronic ballast. Otherwise the LED Lamp witll get flicking, burnt, smell, damaged. How to bypass the ballast? 1. Turn Off the Power. 2. Find the Ballast. Usually it is embeded inside the ceiling fixture. Pls pull off the existing PL lamp, reflector. Leave wire in junction box. and find the ballast. 3. Normally, the Ballast has a black and white wire on the input side (AC input side, 100V -120V for North America). It also has two red and two blue output wires. To bypass this ballast, please cut all the Input and output wires, so total 6 wires cut. 4. Then, you can connect the two red wires to the black wire. 5. Next, connect the two blue wires to the white wire. now ballast is bypassed.
⚠️ WARNING (California Proposition 65): This product may contain chemicals known to the State of California to cause cancer, birth defects, or other reproductive harm. For more information, please visit www.P65Warnings.ca.gov.
WELCOME5: Use code WELCOME5 for 5% off on your first order
